All Your Questions Answered
Where can I purchase Plas-Tex®?
Content 1In many parts of the country Plas-Tex® interior wall panels are available at Home Depot, Lowe’s & Menard’s retail stores. All Do-It-Best member stores carry or can special order our products.
Can I coil up Plas-Tex® to bring it home from the store?
Content 1Yes! Plas-Tex® panels may be coiled up to fit in your vehicle for short periods of time. After you get them home, lay them on a horizontal surface so that they can regain full flatness. This may take up to 24 hours.
Are there moldings available for Ploy-Wall™?
Content 1Plas-Tex® Poly-Wall™ is about .060″ (1/16″) thick and is easily installed with caulked seams. Many retail stores carry rigid PVC moldings that may be used with Plas-Tex® Poly-Wall™.
How much of Plas-Tex® is recycled?
Over 95% of the plastic in our product is reclaimed post-industrial scrap that would otherwise go to landfills.
Is Plas-Tex® really 100% waterproof?
Yes! And it’s waterproof all the way through!
Do the Plas-Tex® colors always match?
As with all manufacturing, slight color shifts can occur from lot to lot. Be sure to buy all the panels you need for your project at one time.
Can I use Plas-Tex® outside?
Plas-Tex® interior wall panels are designed for interior use only.
Can I line my garage with Plas-Tex®?
Because of the thermal expansion rate of the recycled plastic used in Plas-Tex®, applications must be in the temperature controlled parts of a building or residence.
I can’t find the adhesives listed on the Plas-Tex® label.
For non-porous surfaces you can use our Parkland Panel Adhesive (special order from Parkland Plastics) or 3M™ HI-Strength 90 spray adhesive. For Porous surfaces, you can use Liquid Nails® FRP #310 (Trowel-able adhesive in a bucket), Liquid Nails® LN320 (Trowel-able adhesive in a bucket), and Franklin Titebond Fast Grab FRP Adhesive (Trowel-able adhesive in a bucket). For more information please call us at 800-835-4110.
Can I use adhesive in tubes to install Plas-Tex®?
All recommended glues for .060″ & .090″ Plas-Tex® interior wall panels are trowel style latex adhesives. Plas-Tex® requires a continuous adhesive bond.
Can I install Plas-Tex® with solvent based adhesive?
Adhesives that contain flammable vapors are not recommended for installing .060″ & .090″ Plas-Tex® interior wall panels.
Can I install Plas-Tex® with rivets or screws?
Rivets or other mechanical fasteners may be added after installation with a recommended adhesive to meet specific building requirements. Ensure that sufficient space is allowed around all fastener shanks to allow for movement.
Should I use any Caulk with Plas-Tex®
For a watertight installation, we recommend the use of 100% silicone caulking with our interior wall finishes.
Where can I find moldings for the PolyWall™?
The store from where you purchased the PolyWall™ will likely stock moldings. Be sure to fill the channel of the molding with a bead of silicone caulk to seal the gap between the molding and the panel.
Can I use Plas-Tex® panels in my RV?
This is not recommended. The temperature range in an RV is too wide.
Why isn’t Plas-Tex® recommended for ceiling applications?
The glue used for Plas-Tex® requires a couple days to achieve its full strength. This makes a ceiling application extremely difficult as extensive bracing is required. We recommend using one of our factory laminated panels for ceiling applications.
Why isn’t Plas-Tex® recommended for inside garages?
The wide temperature range in a garage makes the installation very difficult and problematic. We recommend using one of our factory laminated panels.